AISLF1- Austenitic Stainless Steel

Steel data sheets

Choose the measure unit in which display the data:

Valbruna Grade

AISLF1

Steel type

Austenitic Stainless Steel

Description of material

AISLF1 is a low Carbon Cr –Ni austenitic stainless steel with a good general corrosion resistance as well as good intergranular corrosion resistance after welding processes. This grade has been designed in order to offer a good hot plasticity (forge-ability) thanks to an exact chemical balance of elements such as Carbon, Nitrogen and Nickel. AISLF1 is particularly suitable for heavy forging processes.

Applications

AISLF1 is suitable for the fabrication of many products such as flanges, valves, bolting, pump shafts, food /beverages industry equipment, storage tanks, many organic chemicals and parts working in mild to medium corrosive environments.

Melting practices

Argon Oxygen Decarburization

Corrosion resistance

AISLF1 is resistant to fresh water, many organic chemicals and inorganic compounds, atmospheric corrosion, rural applications and sterilizing solutions where the chloride is low. Pitting and crevice corrosion may occur in chloride environments if concentration, pH and temperature are at determinate levels. As with other standard austenitic grades, AISLF1 suffers from stress corrosion cracking about forty degrees (C°) above room temperature and above certain levels of stress and halogen concentration. Very Strain hardened structures increase the risk of stress corrosion cracking, but its intergranular corrosion resistance is good. It should be noted that this grade, as for every kind of stainless steel, surfaces should be free of contaminant and scale, heat tint, and passivated for optimum resistance to corrosion.

Machinability

Austenitic grades are different from Ferritic and Alloy steels and require more rigid and powerful machines in addition to the correct choice of tools, coatings and cutting fluids. The Austenite structure is prone to transform in to α’Martensite caused by strain hardening of the tool on the surface of the machined piece. The knowledge of this behavior must be correctly considered when a piece requires two or several cutting steps to be finished. The layer of α’Martensite is very hard and, if the subsequent turning or milling processes work on this hardened layer, a rapid tool wear could happen. The tool must work under this layer. The very low Sulphur content decreases the machinability of AISLF1 compared to AISLF.

Weldability

AISLF1 has a special chemical composition which helps to avoid solidification cracks in the fused-zone of autogenous welds due to a suitable Ferrite balance and very low Sulphur content. In the case of filler metal welding, the typical ER for type 304 group steels could be used. AISLF1 can be welded without PWHT, such as annealing and fast cooling, due to its low carbon content which avoids the precipitation of Cr-Carbide on the grain boundaries. However, in the case of aggressive environments, a PWHT should be considered.

Hot working

AISLF1 is specifically designed for hot working and is usually supplied as billets, blooms, or ingots. No preheating is required. In Primary hot transformation processes, a high temperature homogenization of large ingots and dynamic recrystallization parameters should be rightly evaluated. In the case of open die forging of large ingots and shapes, AISLF1 offers a good hot plasticity if a suitable soaking and a right temperature are applied. In Secondary hot transformation processes, such as extrusion, rolling or close die forging, temperatures, strain and strain rate should be well considered because they influence the properties of the austenitic structure. Suitable strain in terms of section reduction ( for instance: 15-30%) at a lower range of hot working temperature is recommended in order to obtain a fine grain austenitic structure which is very important for mechanical, fatigue and corrosions resistance properties and makes it easier for ultrasonic testing to detect small indications as required by several International Norms. Small forgings can be cooled rapidly in air or water.

Designations

AISI 304/304L
W.N. 1.4301/1.4307
UNS S30400/S30403
EN X5CrNi18-10/X2CrNi18-9
BS 304S15/304S31
Scroll to top